Owatrol Solid Colour Stain, Exterior Masonry And Wood

Price range: £56.29 through £732.99

Optional Paint Brush

Total: £56.29

£2.95 Next Day Postage. £24+ orders are Free Next Day.

Product Description

SOLID COLOR STAIN is a premium finish for new wood and for recoating old applications. SOLID COLOR STAIN is fortified with OWATROL® E-B* to provide unsurpassed adhesion to vertical and horizontal exterior substrates where other products ultimately fail or require extensive preparation and priming.

Properties

  • Excellent adhesion and flexibility.
  • High traffic performance on deck surfaces.
  • Long lasting on cladding.
  • Easy application. Easy maintenance.
  • Protects against moisture damage.
  • Warrantied against peeling and flaking (see Limited Warranty details).
  • Quick drying. Low odour.
  • Microporous – Allows wood to breathe.
  • High colour fastness.

Surface Preparation

General Directions

  • Surfaces must be clean, dry and free of dirt, grease, grime, mildew and if necessary previous coatings.
  • Treat any mould and mildew with a 50/50 Bleach/Water solution. Scrub solution on to the surface and allow to stand 15 minutes, rinse thoroughly.
  • After cleaning and/or stripping allow wood to dry 2-3 good drying days or until it has reached a moisture content of 18% or less.
  • If necessary sand surface with 80 grit abrasive or coarser (depending on wood species) to remove any raised grain.

New Wood

  • New wood has a hard shiny surface known as mill glaze that prevents maximum penetration; this along with the moisture content and natural oils/resins in new wood prevents the proper adhesion of any coating.
  • Conduct water drop test: Sprinkle water on the surface. If water is absorbed immediately, the surface is ready for finishing, if not proceed as follows:-
  • Resinous and high moisture content timber e.g. Larch, Pine, Spruce, PTW… – Treat with SEASONITE* and allow to weather a minimum of 6 months.
  • Cedar – Treat with SEASONITE* and allow to weather a minimum of 12 months, irrespective of the result of the water drop test.
  • Exotic woods e.g. Iroko, Azobe, Padouk, Ipe… – Allow to weather a minimum of 12 months.

Untreated Weathered wood

  • Clean wood with NET-TROL* to remove all loose wood fibres, dirt and other surface contamination. If wood is severely contaminated clean with AQUANETT* or PREPDECK*. Neutralise with NET-TROL*.

Previously Coated surfaces (Oil, Paint, Stain etc.)

  • Check existing finish for adhesion by using the cross hatch test method.

If existing finish is well adhered

  • Sand surface.
  • Clean with NET-TROL*.

If existing finish is in poor condition and/or poorly adhered

  • All previous coating(s) must be completely and thoroughly removed.
  • Oils: Strip with AQUANETT* or PREPDECK*, neutralise with NET-TROL*.
  • Solvent (oil or alkyd based) finishes: Strip with DILUNETT*, neutralise with NET-TROL*.
  • Acrylic (water-based) finishes: Strip with PREPDECK*, neutralise with NET-TROL*.Other finishes e.g. 2 pack epoxies, urethanes etc.: Strip with DSP800*.

Note: Woods high in tannins e.g. Cedar, Ipe, Oak, Teak will darken when treated with AQUANETT*, PREPDECK* or DILUNETT*. Neutralising with NET-TROL* immediately after rinsing will lighten and restore the woods colour.Note: It is imperative that a contact time test is done when using AQUANETT*, PREPDECK*or DILUNETT* on Oak, Chestnut and other high tannin content woods to avoid blackening the wood – Refer to the relevant TDS.

Application

  • Apply a coat of SOLID COLOR STAIN avoiding heavy application.
  • Allow to dry – 4 hours.
  • Apply second coat.
  • When applying by spray, always back-brush or back-roll immediately after application to ensure uniformity of colour, coverage and penetration.

Technical Data

  • Vehicle Type: Acrylic/Alkyd
  • Solvent Type: Water
  • Specific Gravity: at 20°C (68°F): 1,19 ±0,06
  • Viscosity: Brookfield 2000-3000 cups
  • Solid Content: 49% ±3%
  • Flash Point: Not classified as flammable.
  • Shelf Life: 1 year minimum in original unopened packaging.
  • VOC: EU limit value for this product (cat. A/e) 130 g/l (2010). This product contains max. 129 g/l.
  • Application Tools: Brush, Roller, Spray: Airless (0.17 – 0.21 tip at 1800 to 200psi (124 to 138bar).
  • Dilution: Use as is. Do not dilute.
  • Coverage: 8 to 10m² (86 to 107ft2) per litre per coat. Actual coverage will vary depending on application method, type, texture, age, and porosity of the wood.
  • Drying Times: At 20°C (68°F) and 50% RH:- Touch dry: 1 hour- Recoat: 3 – 4 hours- Fully dry: 24 – 48 hours.
  • Clean-up: Soap and water. If Solid Color Stain is allowed to dry on tools, remove with paint stripper.
  • Storage: Close lid tightly after use and store in original container.
  • Keep from freezing and high temperatures.
Coverage: 8-10m2 per litre
Tools: Brush, Roller, Airless Sprayer
Suitable for: Exterior use
Clean up: Soap & water
Drying Time: 24-48 hours
Re-coating Time: 3-4 hours
Suitable Surfaces: Exterior masonry, new or weathered exterior wood

Additional information

Weight N/A

We are rated 5 star on Trustpilot.

5 Star Trustpilot

100 Day Returns Policy.

On everything, unless stated otherwise in the item's description.

Buy Now For A Cash Reward.

Choose Super at checkout for 5% off of your next order.

Dispatching Everything, Every Day.

We dispatch every single day. We even dispatch on Sundays.

Want Your Order tomorrow?

Pay by 4pm and we'll get your order out today, for tomorrow's delivery.

Free next day delivery.

Buy £24+ of products and pay absolutely nothing for tomorrow's delivery.

Spread The Cost Options Available.

Don't want to pay in full? Pay in 3 instalments & 30 day terms available.