Product Description
AQUADECKS® is a penetrating and bonding wood finish providing a flexible, long-lasting rich, matt finish for all woods, including exotic hardwoods. AQUADECKS® saturates, penetrates and stabilises wood to minimise cracking, warping and other damage caused by moisture and sun.
Properties
- Saturates, penetrates and stabilises wood to minimise damage caused by moisture and sun.
- Can be applied on new or weathered wood.
- Provides a matt finish that accentuates the beauty of wood.
- Premium UV absorbing transoxide pigments.
- Provides a long lasting finish.
- Low odour; fast drying.
- Easy application and easy clean-up with soap and water.
Surface Preparation
General Directions
- Surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew and previous coatings.
- Treat mildew with a 50/50 bleach/water solution. Scrub solution on to surface and allow to stand for 10-15 minutes; rinse thoroughly.
- After stripping and cleaning, allow wood to dry 2-3 good drying days or until it has reached a moisture content of 18% or less before applying finish.
- AQUADECKS® can only be applied to bare wood surfaces or a weathered wood surface that was previously finished with AQUADECKS®. ALL other finishes MUST be completely and thoroughly removed.
- If necessary sand surface after stripping and cleaning (80 grit paper).
New wood surfaces
- New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of any finish; this should be removed prior to application in order to ensure maximum performance of the finish.
- Treat surface with AQUANETT®*, neutralise with NET-TROL®*, alternatively mechanically or manually abrade surface with 80 grit paper. Clean off all loose wood particles. Test wood for absorbency by sprinkling water on the surface.
- If water is absorbed rapidly, the surface is ready for finishing.
Untreated weathered woods
Untreated wood surfaces that have weathered longer than 6 months should be thoroughly cleaned with undiluted NET-TROL®* to ensure that all loose wood fibres, dirt and other surface contaminants are removed.
Previously treated surfaces (oiled)
All oils or sealers must be completely and thoroughly removed with AQUANETT®* and the stripped surface neutralised with NET-TROL®* before applying AQUADECKS®.
Previously treated surfaces (paint, stain, varnish, waterproofers…)
- All previous coatings must be completely and thoroughly removed with DILUNETT®* and the stripped surface neutralised with NET-TROL®* before applying AQUADECKS®.
- Other finishes i.e. 2 pack epoxies, urethanes,…: Contact our technical department for additional information and advice.
Note: Hardwoods inc’ exotic hardwoods and woods rich in tannins i.e. Cedar, Douglas Fir, Teak, Ipe… may darken with AQUANETT®* and DILUNETT®*, neutralising with NET-TROL®* immediately after rinsing will lighten and restore the woods colour.Bamboo Surfaces: Contact our technical department for additional information and advice before starting the work.
Application
- Apply 2 even applications of AQUADECKS® ‘wet on wet’.
- Apply a 1st liberal application of AQUADECKS® and allow to penetrate into the wood.
- Apply 2nd application as soon as the wet look of the 1st application has disappeared (normally 15- 20 minutes) and allow to penetrate into the wood.
- For very porous surfaces a 3rd application may be needed.
- Brush out any puddles within 20 minutes of applying the last application to avoid AQUADECKS® drying as shiny spots on the surface.
- Do not allow AQUADECKS® to become Touch Dry or Dry between applications.
- AQUADECKS®’s place is in the wood not on the surface. Do not create a film on the surface, as this will affect the coatings performance.
Technical Data
- Finish: Matt
- Vehicle type: Acrylic-Alkyd
- Solvent type: Water
- Specific gravity: 1.01 ± 0.05
- Physical state: Liquid
- Solid content: 11% ± 2
- Flash point: Not classified as flammable.
- Shelf life: 1 year minimum in original unopened packaging.
- Container size: 1L, 2.5L, 10L.
- Colour: Honey, Movingui, Teak, Padouk, Weathered Grey, Graphite Grey, Ebony
- Dry time: 4 hours, depending on temperature and humidity. Up to 48 hours for decks depending on weather conditions.
- VOC: EU limit value for this product (cat. A/f) 130 g/L (2010). This product contains max. 47 g/L.
Coverage: | 5m2 per litre per 2 coats |
Tools: | Brush, Roller, Airless Sprayer |
Suitable for: | Exterior & Interior use |
Clean up: | Soap & water |
Drying Time: | 4-24 hours (dependent on humidity) |
Re-coating Time: | Apply ‘wet-on-wet’ |
Suitable Surfaces: | All new & weathered wood |