Owatrol CIP, Rust-Inhibiting Penetrating Primer

Product Description

OWATROL® C.I.P. (Corrosive Inhibiting Primer) is an anti-corrosive primer that possesses the penetrating properties of OWATROL® OIL with the added benefit that it may be overcoated with any coating without the risk of it dissolving. OWATROL® C.I.P. stabilises the surface penetrating deep into the substrate, driving out excess moisture and air to form a solid stable layer. With OWATROL® C.I.P., sand or shot-blasted surfaces do not require immediate priming; a light rust coating will not affect its performance or the final result.

Properties

• Penetrates deep in to rusted surfaces to drive out moisture and air.
• Forms a solid stable layer that other paints can firmly adhere to.
• Ideal for difficult climatic conditions – Tropical or marine environments.
• Exceptional adhesion to clean bright steel.
• OWATROL® C.I.P. completely seals sound underlying metal against corrosion.
• Avoids the need for sand or shot-blasting – Minimal preparation required.
• Resistant up to 175˚C.
• Compatible with all paints.
• Excellent chemical resistance – Corrosive gases, Industrial…

Surface Preparation

• Surfaces must be clean, dry and free from oil, grease and other surface contaminants.
• Remove all mill scale; loose and fl aking rust and old paint back to a sound surface and edge.
• Feather in any sharp edges.
• Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned.
• Severely contaminated surfaces should be cleaned using an appropriate solvent.

Application

Stir well before and during use. Do not thin.New surfaces:

• Prime with 1 coat of OWATROL® C.I.P. and allow to dry.
• For surfaces subject to aggressive climatic conditions apply 2 priming coats.

Clean, lightly rusted or new unpainted rusty steel:

• Apply 2 coats of OWATROL® C.I.P. allowing drying time between coats.

Old severely rusted surfaces:

• Apply 3 coats of OWATROL® C.I.P. allowing drying time between coats.

OR

• Apply wet on wet applications of OWATROL® OIL* until rust is fully saturated and allow to dry 24 hours.
• Apply 2 coats of OWATROL® C.I.P. allowing drying time between coats.

Previously coated surfaces:

• Spot prime all exposed metal with 2 coats of OWATROL® C.I.P. allowing drying time between coats.
• Apply 3rd coat over entire area and allow to dry.

Technical Data

• Finish: Satin.
• Vehicle Type: Alkyd Resins.
• Solvent Type: Solvent.
• Viscosity: Thick liquid.
• Specific Gravity (at 20°C): 0,971 ± 0,05.
• Physical State: Liquid.
• Solid Content: 50,6 ± 3.
• Flammability: Not classified as flammable.
• Flash point: > 60°C.
• Temperature Resistance (Fully Cured Dry Film): + 175˚C.
• Shelf life: 2 years minimum in original unopened packaging.
• Container size: 0.5L, 2.5L, 20L.
• Colour: Brick Red.
• Touch Dry: 6 hours.
• Dry Time: 24 hours, depending on temperature and humidity.
• Re-coating Time: 24-72 hours depending on finish: C.I.P. 24 hours; Oil/Alkyd paints 24-48 hours;
• High Solvent paints i.e. 2 pack, urethane etc 48-72 hours.
• VOC: EU limit value for this product (cat. A/i): 500 g/l. (2010). This product contains max 480 g/l. VOC.