Owatrol Polytrol, Colour Restorer For Dull Or Faded Surfaces Including Car Trims

Product Description

POLYTROL®, which does not contain silicone, is a deep penetrating oil that restores the original look and finish to gelcoat, plastic, metal and other surfaces. Drying to a tough, long lasting, flexible finish, POLYTROL® penetrates deeply, re-wetting the pigments so restoring the colour and lustre, which have been lost through exposure to sunlight, rain and pollution. On bare metals POLYTROL® restores the shine and protects against corrosion.

Properties

• Restores the colour and appearance of dull and faded surfaces.
• Revives and enhances the colour of faded marble, tombstones, slates, tiles inc terracotta tiles.
• Rejuvenates flat and chalky paint work, dulled by weathering.
• Eliminates the need for waxes and polishes that sit on the surface and dry out quickly.
• Restores and protects the shine of polished metals.
• Easy to apply – Easy to maintain.
• Protects against corrosion.

Surface Preparation

General directions

• Surfaces must be clean, dry and free of dirt, grease, grime and mildew.
• All waxes, polishes, silicone etc should be completely and thoroughly removed.
• Treat mildew with a 50/50 bleach/water solution. Scrub solution on to surface and allow to stand 10-15 minutes, rinse thoroughly.

Plastic, gelcoat, tiles, painted surfaces etc.

• Clean surface with warm soapy water or NET-TROL®*.
• Rinse thoroughly and allow to dry a minimum of 24 hours depending on surface.

Stone, brick, etc.

• Clean surface with NET-TROL®*.
• Rinse thoroughly and allow to dry a minimum of 24 hours depending on surface.

Metal

• Clean surface with PURA-TROL* and rinse thoroughly.
• Leave to dry a minimum of 24 hours.

Application

General directions

• Always work in areas that can be completed 10-20 min.
• If surface absorbs POLYTROL® unevenly i.e. matt and shiny patches move surplus oil from shiny areas to matt areas.
• Wipe off excess POLYTROL® with a clean lint free cloth before it becomes tacky.
• For a shinier finish, buff surface with a lint free polishing cloth.

Plastic, gelcoat, tiles, painted surfaces etc.

• Apply POLYTROL® liberally and evenly with a brush or cloth.
• Allow to work 10-20 min.
• Wipe off excess POLYTROL® with a clean lint free cloth.
• Leave to dry.

Stone, brick, etc.

• Apply POLYTROL® liberally and evenly with a brush or cloth.
• Allow to work 10-20 min.
• Brush out or wipe off excess POLYTROL® with a clean lint free cloth.
• Leave to dry.

Metal

• Soak abrasive pad or wire wool in POLYTROL® and apply to surface with a rubbing action.
• Allow to work 10-20 minutes.
• Wipe surface with a cloth to remove all residue.
• Buff surface with a soft, lint free cloth.
• Leave to dry.

Note: POLYTROL® is not a surface coating. Its place is in the surface, not on the surface. Excess POLYTROL® that dries on the surface may be removed with DILUNETT®*.

Technical Data

• Finish: Transparent
• Vehicle Type: Alkyd resins
• Solvent Type: Solvent
• Viscosity: Fluid
• Specific Gravity (at 20°C): 0.857 ± 0.05
• Physical State: Liquid
• Solid Content: 33% ± 2
• Flammability: Not classified as flammable.
• Flash point: > 60°C
• Shelf Life: 2 years minimum in original unopened packaging.
• Container Size: 250mL, 500mL, 1L, 20L
• Colour: Amber
• Dry time: 24 hours depending on temperature and humidity.
• VOC: Out of scope

Restrictions

Do not use POLYTROL® on white surfaces.